Serial Port Data Logger Companies
This is a demo of a data logging sketch that is capable of logging serialdata to an SD card at up to 115200 baud.You must install the SdFat library to use the SerialPortLogger. SdFatcan be downloaded from:Normally the maximum rate for a 328 Arduino is 57600 baud.It is possible to log data at 115200 baud with a 328 Arduino if you use a highquality SD card.Lower quality cards can have an occasional write latency of over 100milliseconds. This will cause a receive data overrun at 115200 baud sincethe RX buffer on a 328 Arduino is 1024 bytes. You need to reduce the baudrate to 57600 if your SD card causes receive overruns.Most SD cards will work with a Mega Arduino at 115200 baud since the RXbuffer is set to 4096 bytes.It is possible to use software SPI on a Mega by setting MEGASOFTSPI nonzeroin SdFatConfig.h.
This will allow a shield like the Adafruit Data Loggingshield to be used on a Mega without jumper wires.The two programs, SerialPortLogger.ino and SerialDataSource.ino, demonstratehigh speed logging of serial data.To run this demo, you need two Arduino boards and an SD shield or SD module.The board with the SD shield should have an LED and series resistor connectedfrom pin 3 to ground. This LED will blink an error code if an error occurs.Make sure BAUDRATE has the same value in SerialPortLogger.ino andSerialDataSource.ino.Load SerialPortLogger.ino into the board with an SD shield or module andSerialDataSource.ino into the second board.Connect a wire between GND pins on the two boards.Connect a wire between the serial RX pin (Pin 0) on the SD board and theserial TX pin (pin 1) on the data source board.It is best to power the two boards with an external 9V supply.After the boards are powered up, wait until the pin 13 LED on the data sourceboard goes out. This will take up to 50 seconds.Insert an SD into the logger board.
Serial Data Logger. Serial port data logger are developed on unique big memory SD card storing technology which doesn’t need special protocl and support standard serial port with transparent protocol. Data is stored at SD card with TXT file and can support 1-8G. For 16G or 32G SD card memory, it can be specially made. Intro: I need to write a small program that reads serial data in real-time and writes it to a text file. I have made some progress with reading the data, but I haven't had any success storing this information in a. RS232 Data Logger and RS232 Logger ActiveX are for monitoring, capturing and logging data from RS-232 ports Managing serial port devices can be a real pain. Monitoring the data exchange process between the device and the computer, logging and structuring serial data into a database - that's the brief common task list of any automation engineer.
Press reset on the logger board. Theerror LED connected to pin 3 should not light.Press reset on the data source board. The pin 13 LED on the data sourceboard should light for about 50 seconds at 57600 baud or 25 seconds at115200 baud while 280,000 bytes are transferred.If an error occurs, the error LED on the SD board will flash an error code.See the SerialPortLogger.ino source for definitions of error codes.Remove the SD and check the file SERIAL.BIN. In this case it is a text file.
Welcome to LinuxQuestions.org, a friendly and active Linux Community.You are currently viewing LQ as a guest. By joining our community you will have the ability to post topics, receive our newsletter, use the advanced search, subscribe to threads and access many other special features. Registration is quick, simple and absolutely free. Today!Note that registered members see fewer ads, and ContentLink is completely disabled once you log in.Are you new to LinuxQuestions.org? Visit the following links: If you have any problems with the registration process or your account login, please.
Serial Port Data Logger Companies List
If you need to reset your password,.Having a problem logging in? Please visit to clear all LQ-related cookies. Introduction to Linux - A Hands on GuideThis guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started guide, with exercises at the end of each chapter.For more advanced trainees it can be a desktop reference, and a collection of the base knowledge needed to proceed with system and network administration.
This book contains many real life examples derived from the author's experience as a Linux system and network administrator, trainer and consultant. They hope these examples will help you to get a better understanding of the Linux system and that you feel encouraged to try out things on your own.to receive this Complete Guide absolutely free. I would like to make a data logger, using the analog inputs from an Arduino, which has serial-over-USB. I want to use a computer running Linux to retrieve the data from the serial connection serial and store it. I want to do it as fast as possible, but I can adjust the sample rate in the Arduino firmware to slow it down as far as needed. My question isn't about the Arduino part, but about the computer part. I know just enough bash and perl to be dangerous.I need a way to grab the serial data from the Arduino and store it in a file.
How do you do that? I know how to use the serial monitor in the Arduino program, but I don't know how to redirect that to a file. Can I just write a bash script like so? Farming simulator 2011 mods pc. Code: cat /dev/ttyUSB0 mydatafile.txtand this just keeps running until I kill it?My hard drive is not infinitely big, so I also need a way to somehow 'scroll' or over-write the file when it gets to a certain size.
I don't know what Linux utility lets you write to the end of a file and delete the first line, but there must be one. If not I guess I can write a perl script to do that constantly, but it might slow things down.The other option would be to create multiple files and delete the old ones as hard drive space fills up. I guess I could do that with perl.I hate to reinvent the wheel so insight is appreciated. Quote:My hard drive is not infinitely big, so I also need a way to somehow 'scroll' or over-write the file when it gets to a certain size. I don't know what Linux utility lets you write to the end of a file and delete the first line, but there must be one.
If not I guess I can write a perl script to do that constantly, but it might slow things down. The other option would be to create multiple files and delete the old ones as hard drive space fills up.Uh. Actually, such ring buffering is only done with data structures in main memory, but never with text files. Even if one could avoid to partially overwrite older lines in a file with newer lines (i.e., by giving all lines a fixed length, padding shorter messages with spaces), such files would be hard to monitor.Instead, a regime of growing, but rotated log files is used. To conserve storage space, log files are regulary renamend/recreated and older log files get kept in compressed form, until these older copies are flushed, too. Take a look in your '/var/log/' directory, where the syslog facility of your Linux keeps its logs. Open a terminal window/tab and try.
The idea of using syslog makes kind of sense, but I intend to pull in records as fast as I can get them from the serial port and store gigabytes worth of data. Does it make sense to use syslog to do this specialized task? I would have to customize everything about syslog (how long files are kept etc).I can not anwser that, because I don't really know how 'special' your requirements are.What does the data sent over serial port look like? Is it text/human readable?How much data per second and per hour? Is a serial line even fast enough?How constrained are you really for storage space?
For how long do you want/need to keep older data?Have you considered other perl logging modules, which don't use syslog? There are whole frameworks of perl modules just for logging, the hard part is to identify something fitting, nice & tasteful.